Menampilkan postingan yang diurutkan menurut relevansi untuk kueri Circuit. Urutkan menurut tanggal Tampilkan semua postingan
Menampilkan postingan yang diurutkan menurut relevansi untuk kueri Circuit. Urutkan menurut tanggal Tampilkan semua postingan

Download Joule Thief Made With A Ferrite Bead From An Old CFL Light Bulb Free

Judul:Joule Thief Made With A Ferrite Bead From An Old CFL Light Bulb
info:Here I make use of an old burnt out CFL light bulb for a Joule Thief light circuit. The ferrite bead/core from the CFL is at most 1/4 inch diameter and can fit in the core of my last circuit with a bit of room to spare. I used about 22 turns of fine (bi-filar=2 parallel wires) insulated wire. Comparing it to #30 gauge as shown in my last Joule Thief light circuit video, this wire seems about only half as wide (maby close to #40 gauge or so: seems slightly thicker than a human hair). If I used #30 gauge wire for this ferrite core then only 15 or so turns on it would be possible and may or may not have worked right.....it could of since the inductance would probalby be about the same as the recomended circuit. A Joule Thief circuit is basically like a "voltage step-up/increase" circuit. Voltage basically is the force that will be available to push the current around a circuit. 1.5V is not enough force or potential to push the current through a white LED light, so a Joule Thief increases that to about 3 to 6 V approximately, but can be more. I put a round ceramic magnet near the coil/transformer of the Joule Thief circuit, and the LED dimmed a bit. I guess the inductance of the coil went up leading to a higher reactance (ie. resistance) in the coil, which would diminish the available current. Some more notes for the value of R, the resistor in this circuit: 1K is the reccomended value (but could be a bit less). The circuit will work, produce some light, and diminishing/lessening brightness up to 300K ohms (300,000 ohms of resistance). For the apparant half-brightness use 50 to 100K, and for 1/3 or 1/4 apparant brightness use 100 to 200K. Expect better battery "life time"/lower current drain as you reduce the LED brightness level. You can use a "variable resistor", perhaps 100 or 200K ; just be sure to put the 1K resistor in series with this as a "safety resistor" incase the knob on the variable resistor is set to 0K for max. LED brightness for the given circuit. This 1K will prevent the transistor or other circuit elements/components from being damaged. So far, with the smaller ferrite/coil/transformer circuit element, than the last circuit, the results seem a bit better so far with this circuit, perhaps less drain on the battery. Probably a more efficient coil construction when the number of turns happens to take up all the available space. Advanced usage: There are some circuits here on YouTube, that basically replace the coil or LED with a stepup transformer (high voltage type I guess) that can light a CFL from a 1.5 volt battery. Someone is selling some nice projects/kits for Joule Thiefs. This is very nice since winding that small coil is not so easy, and even nerve wracking when you have to solder the wires to the rest of the circuit, so it's a good deal:: http://www.madscientisthut.com/Shopping/agora.cgi?product=Energy%20Harvesting&user4=Joule%20Thief%20Kits&xm=on You may even use wires to extend the LED off the circuit board if using this inside some box/holder. This kit above seems to be a very good project for anyone, especially since you don't need to know much about electronics other than hooking/soldering things up to work right, as in an electronic kit maker. You can often get an inexpensive soldering iron at some "dollar stores". This may truely be one of the most "neat and useful" circuits (besides a crystal radio circuit, and simple laser communicator circuit) available. Its good to have some things also like "aligator clip hookup test wire", and a Digtal Multimeter (DMM), for all kinds of circuit measurments and testing, which can be had for under $5 such as from Harbor Freight, etc. I've seen some nice once at Kmart/Sears that have some nice "extra functions" on them such as temperature and capacitance metering to name a few. Later you might even consider an oscilloscope to see the voltage "waveforms" and frequencies to test circuits. A nice Earth Battery / Joule Thief: http://www.youtube.com/watch?v=SO6HrZ-JF34 More data: Voltage source 2500mAh NiMh, 1.2V rechargeable battery: Stays at near about 1.2V area for about 3 days (36 hours.... seems to want to "maintain" this voltage), then drops quickly down to about 0.575V in a matter of 6 hours about, and stays in that voltage area for quite a while (just above 0.5V). At this voltage, the light from the LED has not much use, and it will eventually start pulsing (due to the battery and/or the LED?) at a fast rate, and then more slowly over several hours. This 0.55V is the battery voltage while under load/circuit working, and the battery voltage at that point is about 0.875V without the load/non-working circuit at that point. If this is ran off a 0.5 V solar cell, then the circuit would have to be designed to boost the voltage more....or hook up 2 or 3 small solarcells in series. [ March 11, 2011, update: someone else has a previous similar video: watch?v=ZnNQrYy_Bw4 ]
Upload:15 November 2010
Uploader:mif
Durasi:1:58
Source:http://www.youtube.com/watch?v=J_tJtS0WlsI
klik disini untuk download lebih cepat


Terima kasih.!! Anda telah mengunjungi halaman Joule Thief Made With A Ferrite Bead From An Old CFL Light Bulb Kunjungi terus blog ini untuk mendapatkan update terbaru.!!

Download Joule Thief Pirate Light Free

Judul:Joule Thief Pirate Light
info:This is a simple light fixture made using a modified Fuji circuit Joule Thief and a disposable plastic food container. It lights up an 18" tube pretty well and this is very easy to read by. It throws light 360 degrees around the room and works well. I was planning on using another Jeanna light circuit I made but I must have a short somewhere so I stuck in the Fuji. I will use the new circuit on another light project when I get it fixed. For more information go to Overunity.com in the many joule thief topics. Thanks for watching.
Upload:13 January 2010
Uploader:mif
Durasi:3:10
Source:http://www.youtube.com/watch?v=qE0EtXB_RqE
klik disini untuk download lebih cepat


Longitudinal Dielectricity:And yes, we're ALL in this together, you're one of he good ones Bill, thank you for sharing your discoveries and experiments with all to see and use. Best regards and keep up the good work. Spark gap coming from your boost cap may b beneficial or may be too much on the input. So much to experiment with I feel like my head is going to pop sometimes.
Longitudinal Dielectricity:And by DVD I meant CVS. Autocorrect butchered that sentence.I agree with you,the internet and school.I have a degree in audio engineering which also includes electrical engineering,but now I study the world of true earth energy.I wish they taught us about Nikola Tesla in school but they wanted to bury him.Not possible.I would like to add the ignition coil or a Tesla coil to the output,of the Fuji or CVS circuit,maybe a spark gap to see if it'll step it up as well.But first,the proper grounding.
Pirate Labs:Thank you for saying so. I too was inspired by others doing such things...and so it goes. Hey, we are all in this together right? I have learned more from the folks online than I could have ever learned in any school, including my college degree. Thanks, Bill
Longitudinal Dielectricity:It was your vids that got me interested in ripping apart disposable cameras. The DVD continuous flash cams are SUPER easy to mod as well. Thanks for the inspiration.
schpicasso:@Pirate88179 well I do apologize :D am sorry for bad behavior,,,SORRY - just that I was rely curios to understand all as it should be understood from great experiment... and blur was pissing me of - I'm sorry again sir!!!
Pirate Labs:@shpixi What is wrong with your computer? It is not blurry at all when I view it and many others have replicated this with no problems at all. Probably you should fix your computer before casting insults. I am sure your videos are perfect? Where are they? Bill
schpicasso:...well I got pissed of now, in all joule videos from all users IT IS JUST FCUKING ANNOYING BLURRY focus - why ra fcuk you close up camera when it makes it even worse blurry - God damn it, at least you could learn that from your previous videos (for God sake guys) don't post such a cool electronics with such a crap VIDEO :@ F*ALL
MasterTxJ:@Pirate88179 Thanks, and sure thing I'll upload a video tomorrow gotta get some sleep. :)
Pirate Labs:@MasterTxJ Excellent work! That is great news. I have never really test for longevity so this is good info, and with 3 volts input too. That Fuji is a pretty robust circuit considering what it was designed for. Post a video response here of your light and I will approve it so folks can see it. Again, nice work. Bill
MasterTxJ:@Pirate88179 Just rewatched some of your videos and saw that I had commented here. Thought I might give an update on the camp light I built after seeing this vid. I ended up using 2 D batteries in parallel and I can tell you, that lamp gave a steady light a several of hours every evening and night during that camping trip/vacation. All 3 weeks. I still use it sometimes and it's still the same batteries but you have to stroke your hand over the tube now to get it to light and it's a bit weaker.
Pirate Labs:@zintoit Thanks. A lot of good info over there. I just have no easy way to get a schematic into my videos. I don't think my software supports inserted stills and if I tired to video a drawing, it does not show up at all, or not readable. If you have any questions on building the Fuji circuit, pm me and I will be glad to try to help. It is very easy to do really. Thanks, Bill
Pirate Labs:@zintoit What do you mean long and tedious? Go to the JT diagrams and schematics topic area...ALL drawings are there for many Joule Thief circuits including the Fuji. There are at least 5 different ways to wire a Fuji circuit and you can pick the one that meets your needs. I posted references there to the large JT topic page and location for every schematic in that topic so you can read just the part that deals with that particular circuit. Bill
Pirate Labs:@the1969info The information about this is over at overunitydotcom. The carbon rod is a pure carbon rod used in the welding industry and the mag. block is normally used to protect buried propane gas tanks from rusting. They are as far apart as I can get them here in my little apartment garden area. The more distance, the better. Meridian north/south alignment (not magnetic) and the bottom angle needs to match the dip angle for your area. Bill
the1969info:Hi I really like your videos, I am hoping to find out more about making earth batteries and using joule thief circuitry. Could you do a video about your earth battery with more information about it. Such as what is a carbon rod? or your magnesium block, where does one get that? Also how do you determine how apart they should be from each other? I am trying to find out everything for free, so I can play around with spare parts. I am also trying overunitycom..so much too read.
overunitydotcom:@Pirate88179 Yes, or just try to buy 100 pieces of new softwarm white LEDs from Ebay and put them all in series. This way you can drive them with High Voltage. Better also put a resistor first it with it in series too, so you will not destroy them all, if the voltage goes too high. Good luck. Regards, Stefan.
Pirate Labs:Stefan: Thanks. Yes the feedback idea is a good one, I have not tried that yet. I agree about leds instead of the tubes...much more light and better light for the same power or less. I want to try some of those bulbs that Jeanna has been using. Thanks, Bill
overunitydotcom:The only drawback is, that FL tubes emit these nasty mercury frequencies, which are not good for your eyesight, so better go with many LEDs put in series... This way you have still a small current and can light up many LEDs from the High Voltage. The new soft-warm-white 3000 Kelvin color temperature LEDs are very nice for your eyes.. ! Regards, Stefan.
overunitydotcom:Hi Bill, great idea with the tupperware case and the standing FL tube ! If you make several you can probably light up your whole room with it. If you use a feedback loop from the tube to the battery you can probably recharge the battery also, so it will last much longer and swap then after a few days the battery and recharge them completely with a solar panel. This way you could run your whole flat during the evenings just with these lights. Many thanks. Regards, Stefan.
Pirate Labs:Thank you very much. Bill
Wintermuteai1:Great Job Bill!

Terima kasih.!! Anda telah mengunjungi halaman Joule Thief Pirate Light Kunjungi terus blog ini untuk mendapatkan update terbaru.!!

Download Free energy From Air Circuit part 2/24 Free

Judul:Free energy From Air Circuit part 2/24
info:1 small circuit w/antenna & ground wire, to gather free energy from the air! Paul adds second & third circuit & ground wire, and builds a pole in friends back yard. (2 circuits, 13.84 & 190. microA) New & improved HOW TO videos here, with "no" music in background. Part 1....... https://www.youtube.com/watch?v=uZSvb... Part 2..... https://www.youtube.com/watch?v=pG8RD...
Upload:05 September 2008
Uploader:mif
Durasi:3:8
Source:http://www.youtube.com/watch?v=EYYysBEwA6w
klik disini untuk download lebih cepat


Terima kasih.!! Anda telah mengunjungi halaman Free energy From Air Circuit part 2/24 Kunjungi terus blog ini untuk mendapatkan update terbaru.!!

Download Joule Thief Surplus Flash Circuit Lights Free

Judul:Joule Thief Surplus Flash Circuit Lights
info:These are two JT lights I made utilizing a no name surplus flash circuit I obtained from Electronics Goldmine for $.69 each (US). These boards were designed for an AA battery and appear to be almost as good (not quite) as the AA Fuji boards, which I find very hard to find around here anymore. These look very similar to a Kodak board but I did not find any matching schematics. Hacking these boards turned out to be simple. Just make sure to discharge the large cap prior to modification by using an insulated handled tool. These boards put out high voltage so, if you do not know what you are doing, do NOT attempt this at all. The high voltage can cause serious injury or death. More information at Overunity.com in the Joule Thief topic area. So, this is very cheap to make: $.69 for circuit board, $7.00 for the 27 chip Lights Of America LED bulb, $2.00 for the box and a little wire, an on-off switch, some neos and a little paint. They operates on free "dead" depleted batteries and put out a lot of light for a very long time. Avast. PS The LOA bulbs do not require gutting or modification.
Upload:27 May 2013
Uploader:mif
Durasi:6:1
Source:http://www.youtube.com/watch?v=tIF7AylcISw
klik disini untuk download lebih cepat


Michael Brymer:Remake this video please. Too blurry and unless you have been doing this before difficult to understand.
muddymuddymuddmann:i just found the old one i made a few years ago after watching your vids. i tested it, and got bit again. I decided to stick it down to a wooden panel with some silicone sealant. Man it's much easier to handle now.. lol. MUDDy
Pirate Labs:I still get bit every now and again....it still hurts and you would think I would know better.....ha ha. Yes, no more CFL's for me....they break and have mercury. These LOA bulbs are great, bright and cheap. The plastic "bulb" part is practically indestructible too. Bill
DiyEcoProjects:HI Muddy / Bill... i made one a while back to power a CFL but the one bill has with led bulb seems Waaaayyy better. I'll have to dig the board out. Also it gave me a nasty bite one time LOL never again. Be careful everyone
muddymuddymuddmann:YOU GOT THAT RIGHT. THANKS BILL. MUDDY
Pirate Labs:Thanks man, I really appreciate it. Bill
Pirate Labs:Thanks MuDDy. Cheap boards while you can get them. Bill
Pirate Labs:Hey, it's a $40 mini cam I bought 4 years ago. It is all I can afford at the moment. It does shoot HD though.
GBluer:Great Video Bill, looks like a very nice camping light.
Raymond Earle:Great audio tutorial. Pity video quality was down. Unfortunately Goldmine don't ship to UK. Many thanks.
muddymuddymuddmann:SWEET! NICE VIDEO. I WANT ONE. MUDDy
Brian Smith:You know great information but very poor video, please use manual for close up shots.
Pirate Labs:Thank you very much Kyle, I really appreciate that. Very cheap boards while we can get them. Bill
KyleCarrington:great work bill, very doable approach to awesome camp lights
Pirate Labs:Very cheap to make and they put out a lot of light. Bill

Terima kasih.!! Anda telah mengunjungi halaman Joule Thief Surplus Flash Circuit Lights Kunjungi terus blog ini untuk mendapatkan update terbaru.!!

Fuji Circuit Joule Thief LED Light / 1

Judul:Fuji Circuit Joule Thief LED Light / 1
info:i saw so meany fuji circut video, and I wan to tray and build one , well i did , this realy works it is crazy but true realy dos work , i got fuji camera and light bulb 120V 4 watt LED light for me works the best and the most light ,did work with cfl to 13 watt but not as much light with this 4 watt led it is crazy bright anyway just wan share with all you guys out there have funn tray it is cool
Upload:05 March 2012
Uploader:mif
Durasi:5:58
Source:http://www.youtube.com/watch?v=YYXhfxbdCxs
klik disini untuk download lebih cepat
fidel catsro:I bet they last much longer with D sized alkaline battery with a small 5 ohm resistor or so to hold back too much current from entering the board
fidel catsro:I don't have Fuji disposables in my neighbourhood..tried it with Kodak disposables and didn't work as well..ive ordered some Fuji from elsewhere and I will definitely pursue this observation..thank you
pushka48:you got to find right spot man , make shore you did not damge you bord wen u got open
Mervin Govender:I tried a 100-240V LED and it lit the led but only flashes. Any reason. Led is 3W.
pushka48:you got too know were to man ....look round and close by transformer is spot they are 2 spots and u have to have under 5watt light 120 volt or other will work for me 120 volt 3 watt led works the best and last 5 hr on one 1.5 volt battery , thanks and good luck
Mervin Govender:I tried a 3W LED Downlighter =35 W Halogen ; 12V but it does not light. There is 60 Led. the voltage on the box is MR16/12V. Please help.
pushka48:yes sir will work
Mervin Govender:Can a 3W 12V Led work with this?
WAYNE SMITH:I live in Jamaica but my question is " can someone show me exactly where to make the connection"
L.Weisler Ghee:it works but they get hot.... :(
pushka48:no they dont get hot at all
pushka48:lights run for 4 hr on regular battery , for diagram working on wen I have time bean working on some other thinks you know , thanks for watching
L.Weisler Ghee:how long did you ran testing for the lights?
L.Weisler Ghee:where can i see a diagram?
pushka48:I will post soon diagram for this
pushka48:it is both 110V-220V 5 watt led
Pavel Ponomaryov:Is this led 110v? I tried this hack with 220v 2w bulb and it did not work. Looks like fuji does not provide enough current, even though voltage is high
pushka48:just goo and look for joule thief diagram and u will find all kind of them made from difrent pepole , thanks for watching
25slim82:any one have a diagram for this? i want to build one
pushka48:no not realy you have to finde right spot and you will light big , you cane finde round transformer thx for wachting if still have problem finde it let me know

Terima kasih.!! Anda telah mengunjungi halaman Fuji Circuit Joule Thief LED Light / 1 Kunjungi terus blog ini untuk mendapatkan update terbaru.!!

#Fuji,#Circuit,#Joule,#Thief,#LED,#Light,#/,#1,

Download DC Boost Converter - A single inductor Joule Thief Free

Judul:DC Boost Converter - A single inductor Joule Thief
info:How to build a simple Joule Thief style DC boost converter using a few basic components. This circuit requires just two resistors, two transistors (NPN and PNP), and a small axial inductor. With an additional diode and capacitor it will also run a rainbow flashing LED from a single AA cell. With a full explanation of how the circuit works.
Upload:24 August 2014
Uploader:mif
Durasi:13:38
Source:http://www.youtube.com/watch?v=EfSveRWJLPw
klik disini untuk download lebih cepat


Jim Conner:Good vid, and a good explanation of a boost converter, but you need to work on the efficiency of that thing. When you remove the green LED from the circuit (thereby removing the load) the input current drops by just 0.7mA (down from 37.0mA to 36.3mA).

Terima kasih.!! Anda telah mengunjungi halaman DC Boost Converter - A single inductor Joule Thief Kunjungi terus blog ini untuk mendapatkan update terbaru.!!

Download Inverting A Joule Thief Free

Judul:Inverting A Joule Thief
info:This is an altered Joule Thief circuit that runs a modified CFL on 12 volts at about 1 amp. The coil is wound on a solid ferrite rod instead of a Toroid shaped core. Three windings of 30 gauge wire make up the coil. Two 20 turn wraps and one over those of 450 wraps. Two small .047uf capacitors and one 20 ohm resistor were added to the circuit. This is a BEMF charging circuit but in the video a large capacitor is used instead of a battery to capture the energy.
Upload:14 March 2009
Uploader:mif
Durasi:7:54
Source:http://www.youtube.com/watch?v=L4EB2x9dHS8
klik disini untuk download lebih cepat


Terima kasih.!! Anda telah mengunjungi halaman Inverting A Joule Thief Kunjungi terus blog ini untuk mendapatkan update terbaru.!!

Download Joule Ringer running on 10v - 10,000uf caps.ASF Free

Judul:Joule Ringer running on 10v - 10,000uf caps.ASF
info:This is my Lasersaber Joule Ringer replication running on a bank of four 10 volt / 10,000uf electrolytic capacitors. A 9 volt battery is used to charge the cap bank. The small modified CFL will stay illuminated dimly for about 3 miuntes. The amp draw is about 4 mA at this light level.
Upload:14 January 2011
Uploader:mif
Durasi:3:6
Source:http://www.youtube.com/watch?v=7Mrk1P_5p0w
klik disini untuk download lebih cepat


camelsonhorizon:open communities arrrrrrrr awesome
Cosmic Gnarler:Thank you Lidmotor for doing this replication. the only thing I think that "you may have done wrong" is maybe the coil may have been too small. I dont know. But I think that this circuit may have potential. Heres a Lark, Try hooking this to the output of a slow pulse motor! Your run time of 3 minutes could easily be topped off by a spinning thing. Other then that, Thank you for your work and descriptions. ... time to feed the baby.
egn83b:hey lasersabor did the capacitors in series but best of luck.
mikrovolt:I have your circuit on simulator and I did see the blip rings every so often. I doted the input it finally put 5X that at 50Khz it lasted a while and I think that it is not easy to get kodak to oscillate right. I think your replication is very good. The kodak transformer uses 6T #25 :: 1750T #45 the other coil the trigger coil is 12T#33::450T#45 so modifying it to run an NS bifilar into this may be tedious. as more info is released adjusting your NS coil may lead to the strong 50Khz

Terima kasih.!! Anda telah mengunjungi halaman Joule Ringer running on 10v - 10,000uf caps.ASF Kunjungi terus blog ini untuk mendapatkan update terbaru.!!

Download Joule Ringer with Bulb Free

Judul:Joule Ringer with Bulb
info:Joule Ringer von Romanoff mit Birne Запитал лампу от ОРФ (Осциллятор Романова на Феррите) без увеличения потребления
Upload:24 August 2012
Uploader:mif
Durasi:39
Source:http://www.youtube.com/watch?v=zhxFcyh-CuM
klik disini untuk download lebih cepat


Pirate Labs:Nice work. This is a great circuit Lasersaber designed. Bill

Terima kasih.!! Anda telah mengunjungi halaman Joule Ringer with Bulb Kunjungi terus blog ini untuk mendapatkan update terbaru.!!

Download Experiment electricity with saltwater Free

Judul:Experiment electricity with saltwater
info:NOTICE: replicate this experiment can be very dangerous, only by people with knowledge of electricity. This experiment is only a simple demonstration for those who does not have enough knowledge in the electric field to understand the importance of salt dissolved in water, triggering an optimal condition the passage of electric current between the two electrodes. *For guarantee success, the working voltage must be in DC, AC voltage does not guarantee the proper functioning. MATERIALS: 1) DC 220V, alternatively AC 220V, but little power performance. 2) A light bulb 230V 500W or 5 bulbs of 230V 100W. 3) Two iron nails or other conductive metal. 4) A glass tray. 5) Water and salt, at least two spoons. 6) Two electric wires.
Upload:19 June 2014
Uploader:mif
Durasi:4:57
Source:http://www.youtube.com/watch?v=ODbgKXFED5o
klik disini untuk download lebih cepat


Alex Trevino:aint nothing new we use a pill contaner in prison all day to light cigs
jogga singh teidy:Where is the other red wire connected to?
destiny vanderlip:We are doing this project 😂 #fun
muhammed abdulrahman:How can I get the manuscript and the materials needed for three bulbs only. So it can serve in the absence of light.
Xrip100:if i have 20% 30% 40% concentration of salt the better it conducts?...or at some point it's useless to add more salt?
Christine Gloria Aoanan:What if i do not use a generator, will it light up the bulb? Am I collecting energy and depositing it in the generator? Very useful but I need to do some experiments so that I won't pay electric bills anymore.
Ricardo Pbautista:h2O + nacl will yield hcl , an acid..., and so your basic battery as a result of chemical reaction..., electron flow in the circuit..., whoala.....light !
Adam Simonini:I was just reading about icon bonds in my textbook. It mentioned that solutions containing dissolved ions are electrolytic, and that the polarity of water interferes with ionic bonds. So... I went to check for a YouTube video of this and voila!
женя боцманов:http://m.youtube.com/watch?v=hmvmi-mk2jUфаза-заземление,заземление-лампа-заземление.
mike:you should explain what is that APARATUS :(
Alba Reyes:Esto es increíble.
Con razón dicen que nosotros somos la sal. ~.~
This is incredible. Rightly they say that we are the salt. ~.~
Mahenaaz Khan:that's sooooooo cool
Steve Johnson's Random Videos:does it work on a computer coolling fan
Tomasz Ferre:sparkling atoms form rod
Leon Guinto:Engineer Aisa Mejino will have scholarship in the US invited by Barack Obama then forever she'll working in the US, become american citizen and all her invention will be mass produced and be sold in the Philippines thrice the price, who be reaping the profits? The Americans, inutil ang govt natin, kc dito priority puro pulitika, si Kris Aquino at high society!
Peter Muzycki:Why does it turn yellow?
electro kid:only reason I watched this to get more electric power to get powerful
Mansi Shahi:that's nice
harshit sanaala:for what did he connected the wires

Terima kasih.!! Anda telah mengunjungi halaman Experiment electricity with saltwater Kunjungi terus blog ini untuk mendapatkan update terbaru.!!